2021-2022 College Catalog [ARCHIVED CATALOG]
|
ATT 202 - GPS Navigation and Auto Pilot Installation 5 Credits, 7 Contact Hours
3 lecture periods 4 lab periods
Principles of Global Positioning Systems (GPS) and autopilot systems installation. Includes substantial application of systems, processes, and installations introduced in ATT 201 , such as installation planning for electrical system requirements, typical mounting, wiring methods, connectors, antenna installation, and operations and use by flight crews. Also includes pre- and post-installation verification of system integration, functional testing, and troubleshooting on GPS and autopilot systems. Also includes an introduction to the installation of engine indicating instruments and their relationship to the instrument console.
Prerequisite(s): ATT 104 and ATT 201
Information: Additional self-paced independent course study materials are required for non-certified Airframe and Powerplant students.
Course Learning Outcomes
1. Perform a specific flight characteristic unique to a component of an aircraft.
2. Illustrate individual flight control surfaces and their relationship to the autopilot system.
3. Plan and execute a flight plan using Visual Flight Rules (VFR) planning techniques.
4. Develop and perform a flight plan using Instrument Flight Rules (IFR) planning techniques.
5. Display, through the use of a flight simulator, a go-around maneuver.
6. Describe the National Aerospace System (NAS) and explain how it applies to avionics.
7. Describe the integration of an advanced navigation system.
8. Demonstrate ability to remove an older system and install a modern system.
9. Troubleshoot and perform functional test on existing and newly installed equipment.
10. Modify and design existing schematics to replicate new installations.
Outline:
I. GPS Communication Radio Operations and Installation
A. System requirements
B. Application of electrical power
C. Frequency selection
D. Squelch and volume adjustments
E. Transmit and receive functions
F. Typical mounting and installation of hardware
G. Typical wiring methods
H. Antennas
I. Troubleshooting techniques
II. GPS Operations and Installation (Moving Map)
A. System requirements
B. Application of electrical power
C. Data cards and memory
D. Receiver modes
E. Page functions
F. Function checks
G. Typical mounting and installation of hardware
H. Typical wiring methods
I. Antennas
J. Troubleshooting techniques
III. Pitot Static systems
A. Airspeed indicator
B. Altimeter
C. Vertical speed indicator
1. Pitot tube
2. Static ports
3. Troubleshooting
IV. Sensing
A. Pitot static and static sensing
B. Total air temperature sensing
C. Altitude versus indicated airspeed (IAS) to Mach
D. Mach meter
V. Air Data Computer
A. Static pressure input
B. Pitot pressure input
C. Air temperature inputs
D. Computer outputs
VI. Forces of Flight and Control Surfaces
A. Lift versus attitude
B. Angle of attack (AOA)
C. Angle of incidence
D. Effects of AOA
E. Equilibrium of forces
F. Aircraft control surfaces
1. Airfoils
2. Primary flight controls
3. Secondary flight controls
G. Control surface actuation
H. Elevator
I. Elevator feel systems
J. Artificial feel systems
K. Aileron
1. High speed
2. Low speed
L. Rudder
VII. Autopilot (AP), Flight Directors (FD) and Flight Guidance (FG) Systems
A. Flight Guidance
B. Servos
C. Control surface actuators
D. Rudder yaw dampener
E. Accelerometers
F. Flight Guidance System
G. Typical control panels
H. Controller
I. Mode select
J. Force limiting
VIII. Roll Channel Heading Selection Modes and Roll Computer
A. Attitude stabilization
B. Turn control rate gyro
C. Roll accelerometers
D. Rate limiters
E. Lift compensation
F. Force transducers
G. Roll heading select modes
H. Heading select mode
I. Heading hold and roll error
J. Beam sensors
K. Flight director roll interface
L. Roll Computer
1. AP disengage FD heading select
2. AP altitude hold mode
3. AP control wheel steering mode
4. VOR capture
5. DC integrators
6. AC integrators
7. Mechanical integrators
8. Autopilot pitch channel
9. Attitude hold
10. AP FD pitch channel interface
11. Attitude hold mode
12. Altitude pre-select circuit
13. Disengage mode
14. Vertical speed mode
15. Altitude capture mode
16. Mach hold mode
17. Airspeed hold mode
18. Control wheel steering mode
19. Flare mode
20. FD go-around mode
21. Stabilizer trim system
IX. Autopilot Control System and Mounting Hardware
A. Typical installations
B. Location of equipment
C. Equipment mounting
D. Routing of cables and bundles
X. Autopilot Maintenance
A. Inspection methods
B. Functional testing
C. Typical repairs
D. Master Minimum Equipment List (MMEL) of system
Note: This is an accelerated overview course. It is the responsibility of the student to use supplemental information on subjects that are not fully understood. At the instructor’s discretion, a student without a current “A” airframe certificate issued from the FAA in good standing will be required to review and test on supplemental material available (on CD-ROM) for check out from the Aviation Technology Center’s tool crib. Proof of current enrollment is required.
Effective Term:
Fall 2016
|